STEP 8 IN LR™ : Measure Quality by Oil Analysis

STEP 8 IN LR™ : Measure Quality by Oil Analysis

Designing a World-Class Oil Analysis Program

The impact oil analysis can have in helping improve equipment reliability and maintaining production uptime is huge. From providing a predictive early warning of impending failure, to seeking a proactive root cause solution, there can be little doubt that oil analysis is an effective condition-monitoring tool

 

What exactly is involved in designing an oil analysis program that provides maximum payback?

 

Steps to Designing a World-Class Oil Analysis Program

Developing an effective oil analysis program requires careful planning. The program should be developed with a careful game plan in place based on a stated series of reliability goals. There are five basic steps to developing an oil analysis program:

 

5 basic steps to developing an effective oil analysis program

Tabel 1

 

To maximize the opportunities for success, these steps should be performed in this order so that the program is developed on a sound footing.

 

 

Step No. 1: Initial Program Setup

The overall structure and foundation of an oil analysis program should be based on sound reliability engineering goals. These goals should guide the end user through the process of designing and implementing the program.

 

While the lab’s experience in developing effective oil analysis programs can be used to support the design process, it is ultimately the end user’s responsibility to ensure the program meets the company’s goals and reliability objectives. In particular, attention should be paid to the types of test procedures used by the lab under different circumstances.

 

Program design - including test slate and procedure selection - is dependent on end user defined goals.

 

 

Step No. 2: Sampling Strategy

Of all the factors involved in developing an effective program, sampling strategy has 

perhaps the single largest impact on success or failure. With oil analysis, the adage “garbage in, garbage out” definitely applies. While most oil analysis labs can provide advice on where and how to sample different components, the ultimate responsibility for sampling strategy must rest on the end user’s shoulders.

 

While bottom sampling can be useful in determining the presence of unusual levels of water, sludge and other debris, it is unlikely to yield any meaningful data from an oil analysis lab. Of course, sample strategy involves more than just sampling location. Sampling method and procedure, bottle cleanliness and hardware all factor into the sampling equation.

 

Perhaps second only to location in importance, is the provision of collateral information when the sample is submitted to the lab. For industrial equipment, as few as one sample out of 10 is submitted to the lab with appropriate information about oil type, hours on the oil, filter changes or the addition of make-up oil. Without suitable information, oil condition parameters such as viscosity or acid number cannot be compared to the new oil and trend analysis cannot be performed effectively.

 

Without exception, it is the responsibility of the end user to ensure that any and all pertinent information that can be used by the lab in the analysis and interpretation of the data be sent to the lab with each and every sample. Failure to do so simply means that the lab is guessing at whether or not any of the data is significant and should be flagged for attention.

 

 

Oil analysis program designStep No. 3. Data Logging and Sample

 

Analysis
Assuming the sampling strategy is correct and the program has been designed based on sound reliability engineering goals; it is now up to the lab to ensure the sample provides the necessary information.

 

The first stage is to make sure the sample, and subsequent data, is logged in the correct location so trend analysis and rate-of-change limits can be applied. That is the lab’s responsibility.

 

Once the sample has been properly set up at the lab, the actual sample analysis is next.

 

This is an area where end users are definitely at the mercy of the lab and its quality assurance (QA) and quality control (QC) procedures.

 

 

Figure 2: Oil Analysis Program Design

 

 

 

Steps to a world-class oil analysis program

Figure 3:  Steps to a world class Oil Analysis Program

 

 

Step No. 4. Data Diagnosis and Prognosis

Diagnostic and prognostic interpretation of the data is perhaps the step where the most antagonistic relationship can develop between the lab and its customers. For some customers, there is a misguided belief that for a ¤10 oil sample, they should receive a report that indicates which widget is failing, why it is failing and how long that widget can be left in service before failure will occur. If only it were that simple!

 

The lab’s role is to evaluate the data so that complex chemical concepts such as acid number or the presence of dark-metallic oxides makes sense to people who may have many years of maintenance experiences, but haven’t taken a high school chemistry class in many years. The lab cannot be expected to know - unless it is specifically informed - that a particular component has been running hot for a few months, that the process generates thrust loading on the bearings, or that a new seal was recently installed on a specific component that is now showing signs of excess water in the oil sample.

 

Evaluating data and making meaningful condition-based monitoring (CBM) decisions is a symbiotic process. The end user needs the lab diagnosticians’ expertise to make sense of the data, while the lab needs the in-plant expertise of the end user who is intimately familiar with each component, its functionality, and what maintenance or process changes may have occurred recently that could impact the oil analysis data. Likewise, evaluating data in a vacuum, without other supporting technologies such as vibration analysis and thermography, can also detract from the effectiveness of the CBM process.

 

While the end user must bear some responsibility for correctly evaluating the data, the lab does have some culpability.

 

Step No. 5. Performance Tracking and Cost Benefit Analysis

Oil analysis is most effective when it is used to track metrics or benchmarks set forth in the planning stage. For example, the goal may be to improve the overall fluid cleanliness levels in the plant’s hydraulic press by using improved filtration. In this 

case, oil analysis - and specifically the particle count data - becomes a performance metric that can be used to measure compliance with the stated reliability goals. Metrics provide accountability, not just for those directly involved with the oil analysis program, but for the whole plant, sending a clear message that lubrication and oil analysis are an important part of the plant’s strategy for achieving both maintenance and production objectives.

 

The final stage is to evaluate, typically on an annual basis, the effectiveness of the oil analysis program. This includes a cost benefit evaluation of maintenance “saves” due to oil analysis. Evaluation allows for continuous improvement of the program by realigning the program with either preexisting or new reliability objectives.

 

 fanpro-the-right-test-for-your-equipment

Summary

There can be little doubt that oil analysis is an integral part of any condition-based maintenance program. When used effectively, it can warn of impending failure, direct us to the root cause of a problem, or point to areas of opportunity we perhaps didn’t know existed. However, just like you wouldn’t buy a used car without checking under the hood, taking it for a test drive and kicking the tires, don’t merely assume that filling the sample bottle with oil and sending it to the lab will produce the desired results.

Some years ago EnluseB.V. And Polaris Laboratories started a partnership in Europe. Regardless of where your machines are located, we are ready to assist you in analyzing lubricating oils, hydraulic fluids and lubricating greases. The business model used is unique in the world of analyzing  liquids and oils. It provides you with reliable test results and recommendations.

 

We are pleased that we can offer you this additional service. The importance of proper lubrication can not be emphasized often enough. It's the most important factor for long and trouble-free life of your machines. Oil analyzes play a major role in reducing machine failure. A precise picture is obtained of what is happening in your gearboxes, hydraulic systems, generators, etc. In addition, the analysis provides crucial information about the oil condition. Unplanned production failures and risks of damage to expensive installations are prevented by effective oil controls.

 

Enluse can provide you with economical and easy-to-use oil sampling kits. The samples can then be sent to the laboratories; The default processing time is 24 to 48 hours after receipt. The laboratories are accredited with ISO 17025 and have the latest, automated equipment.

 

In addition to the partnership, we also launched our own private label - FanPro ™ (Fluid Analysis Program).

For detailed information visit our website www.FANPROTESTING.COM.

 

Oil analysis is an essential part of a successful reliability program. An extensive oil analysis can help you check total maintenance costs by anticipating interruptions or extending service life.

 

If you are interested in our analysis services, please contact (tel. +31 (0) 76 57 81 280) or send an email to info@enluse.com.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Reference:

Noria Corporation  - Machinery Lubrication